Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
What're your thoughts about How to Install a Bathtub Yourself?
Setting up a bath tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and also often, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough project. If the old tub is easily accessible, the task can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old tub and also set in the new one. Make certain you have qualified yourself for the task and also fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is far better to think about using one prior to you start. Chances are you may require an expert plumber to make tube connections.
This short article will assist you set up a brand-new tub in your washroom if you have actually already purchased a new tub as well as do not require to transform the setup of your previous water pipes.
Your devices and material checklist ought to make up the following:
Preparing for the Installation
First of all, the supporting frame supplied with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite troublesome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bath tub in the needed placement. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also examine all joints and brand-new pipework for leakages and tighten them if needed. Load the bathtub and also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers are in location in between the faucet and the sink. Secure the tap in place with the producer offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, bring about problems with dampness and feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can break fairly very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is suggested to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Post a remark below. We'd be pleased to hear your thoughts about this posting. In hopes that you come back again soon. Be sure to take the time to distribute this write-up if you enjoyed reading it. Thank you for your time. Visit us again soon.
Check Us Out Report this page